- #Coolterm 104 framing error serial#
- #Coolterm 104 framing error manual#
- #Coolterm 104 framing error verification#
$24 = 25.000 (Homing locate feed rate, mm/min) Mm I just did some more tests with it and it's not reliable.
#Coolterm 104 framing error manual#
#define DEFAULT_TOOL_CHANGE_MODE 1 // 0 = Ignore M6 1 = Manual tool change 2 = Manual tool change + TLS` #define DEFAULT_HOMING_DEBOUNCE_DELAY 250 // msec (0-65k) #define DEFAULT_HOMING_SEEK_RATE 600.0 // mm/min #define DEFAULT_HOMING_FEED_RATE 35.0 // mm/min #define DEFAULT_HOMING_DIR_MASK 0 // move positive dir #define DEFAULT_INVERT_PROBE_PIN 0 // true #define DEFAULT_HARD_LIMIT_ENABLE 1 // true #define DEFAULT_SOFT_LIMIT_ENABLE 0 // false #define DEFAULT_INVERT_LIMIT_PINS 0 // false #define DEFAULT_INVERT_ST_ENABLE 0 // false #define DEFAULT_ARC_TOLERANCE 0.001 // mm
#define DEFAULT_JUNCTION_DEVIATION 0.02 // mm #define DEFAULT_STATUS_REPORT_MASK 1 // MPos enabled #define DEFAULT_STEPPER_IDLE_LOCK_TIMEĒ55 // msec (0-254, 255 keeps steppers enabled) #define DEFAULT_DIRECTION_INVERT_MASK 0 // #define DEFAULT_STEPPING_INVERT_MASK 0 // #define DEFAULT_SYSTEM_INVERT_MASK 0x3F // #define DEFAULT_SPINDLE_RPM_MIN 0.0 // rpm #define DEFAULT_SPINDLE_RPM_MAX 1250.0 // rpm #define DEFAULT_Z_MAX_TRAVEL 900.0 // mm NOTE: Must be a positive value. #define DEFAULT_Y_MAX_TRAVEL 400.0 // mm NOTE: Must be a positive value. #define DEFAULT_X_MAX_TRAVEL 300.0 // mm NOTE: Must be a positive value. #define DEFAULT_Z_MAX_RATE 2400.0 // mm/min #define DEFAULT_Y_MAX_RATE 2400.0 // mm/min
#define DEFAULT_X_MAX_RATE 2400.0 // mm/min T00:13:41 INFO common.c: Flash written and verified! jolly good!
#Coolterm 104 framing error verification#
T00:13:40 INFO common.c: Starting verification of write complete T00:13:39 INFO flash_loader.c: Successfully loaded flash loader in sram T00:13:39 INFO common.c: Starting Flash write for F2/F4/L4 T00:13:38 INFO common.c: F446: 128 KiB SRAM, 512 KiB flash in at least 128 KiB pages. St-flash write GRBL_Advanced.bin 0x8000000 The other compiled image I'm loading with: St-flash -format ihex write GRBL_Advanced.hex
#Coolterm 104 framing error serial#
It's not returning anything via the serial interface did you set the serial to 115kbaud? $132 = 500.000 (Z-axis maximum travel, millimeters) $131 = 50.000 (Y-axis maximum travel, millimeters) $130 = 10.000 (X-axis maximum travel, millimeters) $27 = 1.000 (Homing switch pull-off distance, millimeters) $26 = 250 (Homing switch debounce delay, milliseconds) $25 = 500.000 (Homing search seek rate, mm/min) $24 = 50.000 (Homing locate feed rate, mm/min)
$11 = 0.010 (Junction deviation, millimeters) Which application do you use for submitting the gcode? Candle? I somewhat think the problem is the $J parameter which is submitted by the universal gcode sender.
0 kommentar(er)
